Why Does a Silicone Press Machine Stop Discharging Material?

hydraulic equipment banner

 

A silicone press machine is essential for transferring high-viscosity silicone sealants and adhesives from bulk drums to downstream filling systems. When a silicone press machine is not discharging, production can stop unexpectedly. Understanding the common causes and applying systematic silicone press machine troubleshooting helps operators identify faults and restore stable material delivery.


What Causes a Silicone Press Machine to Stop Discharging?

 

Several mechanical and material-related conditions can interrupt silicone discharge. The following table provides a practical starting point for troubleshooting.

 

Possible cause

Typical symptom

Recommended inspection

Insufficient hydraulic pressure

Pressing plate moves slowly or stops

Check hydraulic pressure and fluid level

Damaged follower plate seal

Pressure cannot be maintained

Inspect sealing components

Excessive material viscosity

Slow or interrupted discharge

Verify material temperature and viscosity

Blocked discharge outlet

Pressure builds but material does not flow

Inspect pipes, valves and nozzle

Trapped air

Irregular material output

Check venting and priming procedure

 

Important: A running hydraulic pump does not necessarily mean sufficient pressure is reaching the pressing cylinder.


How to Troubleshoot Each Problem

 

A)Insufficient Hydraulic Pressure

Hydraulic pressure provides the force required to push high-viscosity silicone material through the discharge system.If the pressure is insufficient, the pressing plate may move slowly or fail to maintain consistent downward force.

 

Check the following:

- Inspect hydraulic oil level and look for leakage.

- Check the pressure gauge against the machine's specified operating range.

- Inspect hydraulic hoses and connections.

- Check the hydraulic pump, valves and cylinder for abnormal operation.

Do not increase pressure beyond the manufacturer's specified limit to compensate for a mechanical fault.

 

B)Damaged Follower Plate Seal

The follower plate creates a controlled interface with the material inside the drum. A worn, damaged or incorrectly seated seal can allow material bypass or prevent effective pressing.

 

Recommended actions:

- Stop the machine and isolate the power supply.

- Release stored hydraulic pressure according to the manufacturer's procedure.

- Inspect the follower plate and sealing components.

- Check for material buildup or deformation.

- Replace damaged seals with compatible components.

 

C)Excessive Silicone Material Viscosity

Silicone sealants have different flow characteristics depending on their formulation and temperature.

 

Low material temperature may increase viscosity, making discharge more difficult. A formulation that is unsuitable for the selected pressing configuration may also cause excessive resistance.

 

To reduce this problem:

- Verify material viscosity before production.

- Check storage and operating temperatures.

- Confirm that the selected pressing force matches the application.

- Evaluate whether the material requires controlled temperature conditioning.

Do not assume that increasing hydraulic pressure is always the correct solution.

 

D)Blocked Discharge Pipe or Nozzle

Cured silicone residue, foreign particles or hardened material can restrict the discharge passage.

 

Inspect:

- Discharge pipe connections.

- Outlet valves and nozzle openings.

- Residual material inside the transfer line.

- Sealing surfaces around the outlet.

Clean affected components using a cleaning method compatible with the silicone formulation and machine materials. Never remove a pressurized pipe or nozzle.


Step-by-Step Troubleshooting Workflow

 

Silicone Press Machine Inspection Sequence

Maintenance and inspection of hydraulic equipment


How to Prevent Discharge Problems

 

Preventive maintenance is more effective than repeatedly correcting discharge interruptions.

 

Maintenance item

Recommended practice

Hydraulic system

Monitor pressure and oil condition

Follower plate

Inspect seals and alignment

Discharge components

Remove residual material after production

Material storage

Follow formulation-specific storage conditions

Control system

Check alarms and operating parameters

 

For production lines handling different silicone formulations, cleaning and material changeover procedures should be established for each product.


How MIC Machinery Supports Stable Silicone Discharge

 

MIC Machinery designs customized hydraulic silicone press solutions for transferring high-viscosity silicone sealants, adhesives and industrial materials.

 

Depending on production requirements, configurations can be adapted through:

- Pressing force and cylinder dimensions.

- Feeding and pressing structures.

- Outlet and nozzle design.

- Control system configuration.

- Integration with cartridge and sausage filling equipment.

For complete adhesive production projects, the press can be integrated with mixing, vacuum processing, storage and filling systems.


FAQ

 

Q1:Can a silicone press machine operate with different sealant formulations?

Yes, provided the pressing system and material-contact components are compatible with the formulation's viscosity, chemical properties and processing requirements.

 

Q2:Does the installation position affect discharge performance?

Yes. Incorrect alignment, unsuitable pipe routing and excessive transfer-line resistance can affect material delivery. Follow the equipment layout and installation requirements.

 

Q3:How should a new silicone press machine be commissioned?

Verify electrical and hydraulic connections, inspect safety devices, check the pressing assembly and conduct an unloaded functional test before introducing material. Follow the manufacturer's commissioning instructions.

 

Q4:When should the hydraulic seals be replaced?

Replace seals when inspection identifies leakage, deformation, wear or loss of pressure-holding performance. Replacement intervals should follow operating conditions and manufacturer recommendations.

 

Q5:Can a silicone press machine connect directly to an automatic filling machine?

Yes. Integration is possible when the discharge capacity, material compatibility, pressure control and filling machine requirements are properly matched.


Conclusion

 

A silicone press machine that stops discharging material may have hydraulic, mechanical, material-related or outlet restrictions. Systematic inspection of hydraulic pressure, follower plate seals, viscosity and discharge components helps identify the actual fault. Regular cleaning and preventive maintenance reduce production interruptions. Proper equipment configuration and integration also contribute to stable silicone sealant packaging.

 

Request a Quote